Cornelius 1400 Service Manual

Service Manual SERIES 1400 (R-22) MODULAR CUBED ICE MAKER 12/91 161951806

STACKING KIT INSTALLATION INSTRUCTIONS FOR MODEL RCV-1204 F 1 - 43547 interface cable 1 - 43534 cover, chute to 2 - 8022 cli plastic 1 - 20928

EX PAN S IO N VALVE U CHECK VALVE 1 I RECEIVER -ACCUM. LINE VALVES f $ REMOTE CONDENSER 11

C LCCTRICAL C I RCU 1 T S E7)UEN-C- N An L.E.D. digit display mounted on the solid state control board will show a status number 0,1,2,4, 66 and a d

ADJUSTMEKT AND CliECK-0111' F,,OR HARVEST-BIN SWITCHES " L CHECKOUT PRQC EUbRE I Turn on the ice machine the evaporator(s). The i 8 secon

I RD 1 G I 1 I BL I' Condensor I RCV 2 Con tro I Rev. F sw I Harvest 8 ~~oc, Bin Switch s OR I LWH Water Dump Switch Reset HDds DC5 Switch I BR B

Water Pump GY CS-I50 Remote Condensor Manual Reset High Pre sure Control RCV-2 Con? rol Rev. F Suction I U==S BRc a SUI To 8tocked Unit- I Dc3 DC3 if

- RD Power Relay Outlet Box 8LI w , @Pressor -RD - Water Pump G AC Ek BL RD I I Manual Reset Condensor ' RD Pressure 3Cocltrol High Fan Motor 1

SANITIZING AND CLEANING PROCEDURE 1. Remove front panel to gain access to the on-off-clean switch. 2. Push switch to "clean" and allow

1 NTRQDUCTI ON We have strived to produce II quality product. thus insuring trouble- free opera tion. This manual has been prepared to assist serv

WATER TREATMENT Automatic ice-making machines can quit working for any number of reasons, mechanical, electrical or faulty refrigeration, but

WINTER STORAGE If the unit is to be stored in an area where the temperature will drop below freezing, it is most important that all water lines b

STATUS 0 1 2 4 6 Decimal Point OFF Decimal mint ON Decimal Point FLASHING STATUS INDICXTOR MPLANATION Unit is in freeze cycle, ding ice, rn problems.

TROUBLE SHOOTING THE SOLID STATE_ CONTROL BOARD To detennine if the circuit board and senmors are functioning correctly under all operating parame

TtROUBLE'SHOOT I N,G THE SENSO,,RS 1. Turn off power 00 machine, ' . 2. 3. Remove the front panel and electrical box cover of the machin

REMOVAL ,O:F~ SOLID ST AT E , C O,N T R~O,L FROM MACHINE CAUTION: THE CIRCUIT BOARD IS FRAGILE, HANDLE WITH CARE. 1. 2. Remove front panel. Turn o

i I I <J>. NO. -7- 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 4

lLLUSTRATED PARIS BREAKDOWN

REMOlE CONDENSER ILLUSTRATED PARPS BREAKDOWN e Illus. No. 1 2 3 4 5 6 7 8 9 10 11 12 Part No. 35832 39898 161 871001 27181 42 145 42624 28627 27384 42

TABLE OF CONT'ENTS INTRODUCTION ... 1 TABLEOFCONTENTS ... 2 ... SPECIFrCATfONS . b . b q 3 t INSTA

Specifications Ambient Temp 'F SERIES 1400 Incoming Water Temp 'F 50. 70' 80' 8011OY VIEW 10' 80' 90' 70' 140

INSTALLAIION INSTRUCTIONS A. UNPACKING 1. Uncrate machine and/or bin by removing the staples from around the bottom of cardboard crate and lift

INSTALLATION INSTRUCTIONS CONT'D. E. REMOTE CONDEWSERS Remote condensers should be installed above the ice machine in a leva1 configuration.

F. MAKE ELECTRICAL POWER SUPPLY CONNECTION Requirements: 208-230/60hz. 1 ph. or 220V 50hz. 1 ph. when used REFER TO SERIAL PLATE FOR MINIMUH CI

INSTALL ATION INSTRUCTIONS CONT'D. Dclnp Valve drain hose ar ;i Taking care not to kink or bllapse vinyl tubing at any point, rbute tubs to any

INSTALLATION INSTRUCTIONS CONT'D. J. STARTING THE UNIT After the ice cuber has been unpacked and leveled and all plumbing and electrical